APR Performance Frontsplitter - 17+ Chevrolet Camaro ZL1 1LE

Item number: CW-601821

Category: Splitter & Diffuser


625,00 €

including 19% VAT. , plus shipping

Shipping time: 32 - 34 workdays



To combat the effects of front end lift, APR Front Wind Splitters are utilized to give extra traction and control in the front of a car. By creating a high pressure area on top of the wind splitter, high pressure air flow is restricted to flow underneath a car. With low pressure below the car, the effect of lift is reduced and a driver can gain from the extra traction and control.

Features:

- Carbon Fiber Reinforcement
All APR Front Wind Splitters are reinforced with sheets of carbon fiber.

- Fully Functional Undertray

The Front Wind Splitters are not just add on cosmetic pieces. Every APR Front Wind Splitter completely covers the entire area below a cars front bumper. This allows for smoother air flow below the front bumper, creating more efficient downforce.

- Support Rods Included
Supporting every APR Front Wind Splitters are stainless steel Support Rods.


Installation Guidelines

The APR Performance Front Wind Splitter (hereinafter referred to as "Splitter") is an aerodynamic tuning component that plays an important role in helping a vehicle achieve aerodynamic balance. Just as there are significant forces acting upon the rear-end of a rear wing-equipped vehicle, there are also significant forces acting upon the front-end of a Splitter-equipped vehicle. To help ensure a smooth installation, please read the following guidelines before you begin any work on the Splitter.

Important Notes ? Must Read!!!

1. Please note that regardless of whether a Splitter is sold as a custom or pre-defined/pre-existing application, all Splitter installations are considered custom installations. There is no such thing as a Plug-n-Play Splitter installation.

2. On a vehicle traveling at higher speeds, a properly-installed Splitter will see anywhere from double-digit to triple-digit downforce numbers. This means there can be a vertical force of up to 100 Pfund (approx 45 kg) or more being exerted across span of the Splitter surfaces. Vehicle speeds and these forces must be considered before any splitter installation!

3. An improperly-installed Splitter may also see the same forces briefly, until it begins to un-mount, tear itself apart, and pull chunks (if not the entire front bumper) away from the vehicle. Don?t let this happen to you!

4. Splitter Support Rods are included with all Splitters. Unless a custom, structurally-reinforced mounting system is professionally-fabricated by a well-qualified race/fabrication shop, the included Splitter Support Rods must be used, and must attach to suitable and secure mounting points (i.e. steel bumper beam, fiberglass structural support, etc.).

5. All Splitters will have some amount of flex built-in. Honeycomb types tend to flex much less than non-honeycomb types of equivalent weight. To maximize splitter efficiency and reliability, it is important to mount the Splitter to the vehicle at multiple points so that flex is minimized. These mounting points include, but are not limited to: front support rods, bolts/nuts to the front bumper or front air dam, rear supporting L brackets, center support brackets, etc. Larger Splitters will need more support than smaller Splitters will need. When the Splitter has been installed, inspect it carefully with the vehicle on a lift. Pull/push on different areas to see where the Splitter is still flexing, and reinforce the weakest areas with additional support brackets.

6. The owner assumes full responsibility for ensuring proper installation. Professional installation by well-qualified personnel is highly recommended. If you have any questions or require additional parts (i.e. longer Splitter Support Rods), please contact us.

Warning

User assumes full responsibility for ensuring proper installation as intended. Professional installation by well-qualified personnel is highly recommended. The vehicle applications shown above are intended to work as a complete system when installed onto original vehicle body parts (i.e. front bumpers, air dams, etc.). To insure proper function and reliability, APR Performance advises against modification or substitution of any component of the intended installation. Any modification or substitution of hardware included with the splitter create unsafe operating conditions and ultimately cause this system to fail. Substitution of original vehicle manufacturer parts needed for the intended installation (i.e. front bumper) with non-original parts may also create unsafe operating conditions and ultimately cause this system to fail.

Average product review

Write your first review and help others with their purchase decision: