Mishimoto Oil Cooler Kit - 18+ Ford Mustang GT

Item number: MMOC-MUS8-18

Category: Cooling

Color / Thermostat:

714,00 €

including 16% VAT. , plus shipping

order item

There are variations of this item. Please select the variation you wish.


Add some extra cooling power to your 2018+ Mustang GT with the Mishimoto Oil Cooler Kit. In 2018, Ford evolved their staple muscle car with a fresh and even more futuristic look on the S550. As the Mustang evolved, Mishimoto evolved along with it to provide optimal cooling for your modern Mustang.

Mishimoto engineers started with designing a heat exchanger from the ground up, to provide the largest oil cooler Mishimoto have to offer and mounted directly to the front of the vehicle for optimal airflow. From there, Mishimoto also developed an application specific mounting bracket that also serves as a diversion panel to further improve the airflow through the cooler. Mishimoto's kit also includes a set of direct fit stainless-steel braided lines for a secure conduit to and from the cooler completed with -10AN fittings for a simplified installation.

Finally, the Mishimoto 2018+ Ford Mustang GT Oil Cooler Kit includes Mishimoto trusted thermostatic oil sandwich plate to protect against the overcooling of your engine oil. Mishimoto's kit is available with the option of a silver or black cooler, and is protected under the Mishimoto Lifetime Warranty for a worry-free installation.

- Direct-fit for the 2018+ Ford Mustang GT
- Innovative bar and plate oil cooler mounts in the upper grille, allowing more room for supercharger heat exchangers
- Mounting bracket also serves as an air diversion panel, directing the maximum amount of ambient air through the oil cooler
- Pre-made stainless steel braided oil lines with durable -AN fittings
- Includes replacement lower radiator hose to bypass the stock fluid-based oil cooler
- Removes the stock fluid-based oil cooler for less stress on the engine's cooling system
- Billet aluminum thermostatic oil sandwich plate
- Increases oil capacity by 1qt
- Mishimoto Lifetime Warranty

Installation Guide: --> Link <--


 

Purchase Includes
(1) – Application Specific Mounting Bracket / Air Diversion Shield
(1) – Bar and Plate Oil Cooler (Silver or Black)
(1) – 2ft 3in Stainless Steel Braided Hose w/ -10AN Fittings
(1) – 4ft 8in Stainless Steel Braided Hose w/ -10AN Fittings
(1) – M22 Thermostatic Sandwich Plate
(1) – Application - Specific, M22 x 1.5 extended length center bolt
(2) – M20 x -10AN Straight Fittings
(2) – 1/8" NPT Plugs
(1) – Large O-ring
(1) - Lower Radiator Hose w/ worm gear clamps
(1) – Mounting Hardware Set
Mishimoto Lifetime Warranty

Notes
Requires the removal of the stock coolant based oil cooler.Installation requires the removal of the active grill shutters. Removal without tuning can cause a check engine light.Recommended torque specification for all straight fittings and banjo bolts: 15-25 ft/lbs (operating range). Do not exceed the maximum torque rating of 35 ft/lbs

Engine Codes: 5.0 Coyote III
Chassis Codes: S-550

PRODUCT SPECS

Material: 6061 Aluminum
Rows: 12
Core Length: 470 mm
Fitting Size: -10AN
Caution: It is the installer's responsibility to check all thermostat plugs, NPT plugs, line fittings, and other connections to assure they are fully tightened before operating the vehicle. Mishimoto recommends that you check all connections at regular intervals, especially during the first few miles after Installation.
Overall Height: 62,8 mm
Overall Length: 726 mm
Overall Width: 311,3 mm
Fluid Capacity: 0,9 L

Average product review

Write your first review and help others with their purchase decision:

Installation Guide